|
|
|
|
|
|
|
|
|
|
|
Item Description：
- Vehicle Location : Trunk
- Extended Length [in] : 10.98"
- Compressed Length [in] : 8.63"
- Patented Multi-Lobe Seal makes gas spring more tolerant to vibration and temperature extremes
- Twin Tube internal construction-Premium gas-charged cylinders
- Direct fit,Ensures easy installation and precise operation
- Individually tested for performance and reliability
- Brand new and warranty offered!!!
This Listing is for 2 Supports which fit the Following Applications：
2005-2011 Ford Focus Base Sedan 4-Door Trunk
-With Out Rear Spoiler
2005-2011 Ford Focus LX Sedan 4-Door Trunk
-With Out Rear Spoiler
2008 Ford Focus S Coupe 2-Door Trunk
-With Out Rear Spoiler
2007-2011 Ford Focus S Sedan 4-Door Trunk
-With Out Rear Spoiler
2007-2011 Ford Focus SE Sedan 4-Door Trunk
-With Out Rear Spoiler
2009-2011 Ford Focus SEL Sedan 4-Door Trunk
-With Out Rear Spoiler
2007-2011 Ford Focus SES Sedan 4-Door Trunk
-With Out Rear Spoiler
2007 Ford Focus ST Sedan 4-Door Trunk
-With Out Rear Spoiler
2005-2011 Ford Focus ZX4 ST Sedan 4-Door Trunk
-With Out Rear Spoiler
2005-2011 Ford Focus ZX4 Sedan 4-Door Trunk
-With Out Rear Spoiler
How to Properly Install a standard Lift support？
1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.
2. Before removing the old lift support,inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.
3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8",then pull the support away from the vehicle and it will release.
4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.
5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.
6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.
Important Notes about Lift Supports：
1. Each support is tested to perform as well as the original units and in many cases to exceed the manufactures specification,please ensure you replace all the supports in the compartment at the same time to ensure proper performance.
2. Lift supports loose pressure over time,even sitting on shelves in most auto parts stores and many of the inventory liquidators on . Our business is lift supports,and we make sure to sell newly produced units,keeping our inventory fresh and rotated.
Item Description：
- Vehicle Location : Trunk
- Extended Length [in] : 10.98"
- Compressed Length [in] : 8.63"
- Patented Multi-Lobe Seal makes gas spring more tolerant to vibration and temperature extremes
- Twin Tube internal construction-Premium gas-charged cylinders
- Direct fit,Ensures easy installation and precise operation
- Individually tested for performance and reliability
- Brand new and warranty offered!!!
This Listing is for 2 Supports which fit the Following Applications：
2005-2011 Ford Focus Base Sedan 4-Door Trunk
-With Out Rear Spoiler
2005-2011 Ford Focus LX Sedan 4-Door Trunk
-With Out Rear Spoiler
2008 Ford Focus S Coupe 2-Door Trunk
-With Out Rear Spoiler
2007-2011 Ford Focus S Sedan 4-Door Trunk
-With Out Rear Spoiler
2007-2011 Ford Focus SE Sedan 4-Door Trunk
-With Out Rear Spoiler
2009-2011 Ford Focus SEL Sedan 4-Door Trunk
-With Out Rear Spoiler
2007-2011 Ford Focus SES Sedan 4-Door Trunk
-With Out Rear Spoiler
2007 Ford Focus ST Sedan 4-Door Trunk
-With Out Rear Spoiler
2005-2011 Ford Focus ZX4 ST Sedan 4-Door Trunk
-With Out Rear Spoiler
2005-2011 Ford Focus ZX4 Sedan 4-Door Trunk
-With Out Rear Spoiler
How to Properly Install a standard Lift support？
1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.
2. Before removing the old lift support,inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.
3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8",then pull the support away from the vehicle and it will release.
4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.
5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.
6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.
Important Notes about Lift Supports：
1. Each support is tested to perform as well as the original units and in many cases to exceed the manufactures specification,please ensure you replace all the supports in the compartment at the same time to ensure proper performance.
2. Lift supports loose pressure over time,even sitting on shelves in most auto parts stores and many of the inventory liquidators on . Our business is lift supports,and we make sure to sell newly produced units,keeping our inventory fresh and rotated.
1.If you want to change the shipping address, please contact us by eBay messages.
2.If you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
3.Payment must be received within 10 days as auction ended or order might be delayed.
1. Orders processed within 24 hours of payment verification.
2. The images shown are not the actual item and are for your reference only.
3. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 30 days to contact us and 10 days to return it from the date it was received.
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Any question, please contact us by email on working days.
We're here for you!
2Pcs Rear Trunk Lift Supports Gas Struts For Ford Focus 2005-2011 W/O Spoiler
Item Description：
This Listing is for 2 Supports which fit the Following Applications：
2005-2011 Ford Focus Base Sedan 4-Door Trunk
How to Properly Install a standard Lift support？
1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.
2. Before removing the old lift support,inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.
3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8",then pull the support away from the vehicle and it will release.
4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.
5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.
6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.
Important Notes about Lift Supports：
1. Each support is tested to perform as well as the original units and in many cases to exceed the manufactures specification,please ensure you replace all the supports in the compartment at the same time to ensure proper performance.
2. Lift supports loose pressure over time,even sitting on shelves in most auto parts stores and many of the inventory liquidators on . Our business is lift supports,and we make sure to sell newly produced units,keeping our inventory fresh and rotated.
1.If you want to change the shipping address, please contact us by eBay messages. 2.If you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement. 3.Payment must be received within 10 days as auction ended or order might be delayed. 1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.
1. Orders processed within 24 hours of payment verification. 2. The images shown are not the actual item and are for your reference only. 3. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! 1. You have 30 days to contact us and 10 days to return it from the date it was received. 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. Any question, please contact us by email on working days. We're here for you! Copyright of The-one-FP. All rights reserved. |
