Welcome to our store!
To avoid you buying the wrong parts, DO CHECK the compatible chart above before placing order.
-
Choose a vehicle from the "My Garage" list. Or
-
Enter your vehicle's details with Year / Make / Model / Trim / Engine. Or
-
Contact us: Ask us for double check.
Fitment:
Chevrolet EQUINOX 2005 - 2009 All Models
Pontiac Torrent 2006 - 2009 All Models
Saturn VUE 2002 - 2007 All Models
Package:
1x Part# Front Right Lower Control Arm + Ball Joint - K621136
1x Part# Front Left Lower Control Arm + Ball Joint - K621129
2x Part# Front Outer Tie Rods Ends - ES800030
2x Part# Front Inner Tie Rods Ends - EV80781
Control Arm Installation Instructions：
Pre-Installation Preparation
- Tool List: Torque wrench, socket set, ball joint separator, jack, safety stands, rust inhibitor, thread locker (optional)
- Vehicle Condition: Park on a level surface, engage the parking brake and secure the wheels, disconnect the negative battery terminal (power off required for electronic system protection on some models)
- Part Inspection: Verify the new control arm model matches, check for no damage to ball joints and bushings, ensure all accompanying bolts and nuts are complete and free of rust
Old Part Removal
- Lift the vehicle with a jack and secure it with safety stands (never rely solely on the jack)
- Remove the wheel and disconnect the control arm mounting bolts from the steering knuckle and frame/subframe
- Separate the ball joint from the steering knuckle using a ball joint separator and remove the old control arm
New Part Installation Steps
- Clean the mounting surfaces (frame and steering knuckle connection points), remove rust and debris, and apply a thin layer of rust inhibitor
- Position the new control arm in place and hand-tighten the frame/subframe mounting bolts (do not fully torque yet)
- Install the ball joint to the steering knuckle, hand-tighten the ball joint nut to ensure full seating of the ball joint
- Install remaining mounting bolts per vehicle specifications, hand-tighten all bolts initially (to prevent misalignment)
- Lower the jack to place the wheel on the ground, ensuring the vehicle is in a level loaded state
- Torque all bolts sequentially to manufacturer specifications using a torque wrench (Reference Values: Ball joint nut 45-65N·m, frame-end bolts 80-120N·m; always follow vehicle manual for exact values)
- Check control arm clearance: Ball joint should rotate smoothly, bushings must not be twisted, and no interference should occur
Post-Installation Inspection & Debugging
- Install the wheel and torque the wheel hub bolts to specifications
- Reconnect the negative battery terminal, start the vehicle, and check for smooth steering and no abnormal noises
- Four-wheel alignment is recommended (calibrate wheel toe and camber angles after control arm replacement to prevent uneven tire wear)
Safety Precautions
- Use safety stands throughout the process; never perform under-vehicle work without proper support
- Torque all bolts to specified values; over-tightening or under-tightening is prohibited
- Conduct a test drive after installation to confirm no pulling or abnormal noises; stop immediately to inspect if issues arise
Notice:
Please check the model and important parameters before purchase to avoid unnecessary after-sales problems, if you are not clear, please feel free to contact us, thank you for your cooperation!
| Item Specifics | |
|---|---|
| UPC | Does not apply |
| Brand | VaultPro |
| Manufacturer Part Number | 13898738 |
| Manufacturer Warranty | 1 Year |
| Placement on Vehicle | Front, Left, Right, Lower |
| Type | Control Arm & Ball Joint Assembly |
| Universal Fitment | No |
| Control Arm Construction | Forged |
| Items Included | Mounting Hardware |
| Custom Bundle | Yes |
| Interchange Part Number | K621136 K621129 ES800030 EV80781 |
| OE/OEM Part Number | Suspension Kit Control Arms and Ball Joints Assembly,Tie Rod Ends |
| Superseded Part Number | Front Driver and Passenger Side Replacement |
| Adjustable | Yes |
| Modified Item | Yes |
| Kit Parts Included | Control Arm,Tie Rod End,sway bar |
| Kit or Single Part | Kit |
| Greasable or Sealed | Greasable |
| OE Spec or Performance/Custom | OE Spec |
| Surface Finish | Polished, Rust Protected |
| Quantity | 6 Pcs |
| Cross Part Number | 1514337,1522347,1914984,22664783,22684863,2272924,191337 |
| Features | Greasable |
| Finish | Coated |
| Cotter Pin Hole | Yes |
| Material | Alloy Steel |
| Mounting Style | Bolt-On |
About Us:
We are committed to making the best auto-parts products and providing you with better services.
So if you have any quesiton or problem, please fell free to contact us about that.
Payment:
Any payment can be accepted by ebay.
Shipping:
2-8 working days in transit.
Product will be shipped within 2 business days after full payment is received and verified.
USPS, UPS, FedEx shipping will be provided.
Delivery time is about 2-8 business days to most of addresses.
Returns:
30-day free return provided.
Contact Us:
Any quesiton or problem, do contact us please.
We are always online to answer.
Note: Do check the compatible chart before paying the items, or contact us for checking the compatibilities for your vehicles/cars/trucks.
