|
|
|
|
|
|
|
Fitment:
91-94 Ford Explorer
NOTE: Look Above this product description (Item Specifics) for all part numbers, part brands, placement on vehicle and Compatibility.Make sure that is the correct fitment for your vehicle.
Features:
- Guaranteed Exact Fit for easy installation
- 100% BRAND NEW and tested to meet or exceed OEM specifications
- Premium ISO/TS 16949 quality - guaranteed highest quality available
- Engineered for superior durability, backed by industry leading warranty
- These are brand new, not used or junkyard parts.
- Each complete assembly is built to meet or exceed exact OEM specifications.
- High corrosion resistance and long service life. Steel rod is mirco-polished with double chrome plate.
- Newer Valving technology operates in stages based on the velocity of the car.
- Use Teflon bonded piston seal to keep friction down and temperature cooler so that valving stays firmer.
How to install:
Step 1: Before you lift the vehicle, loosen lug nuts one full turn.
Step 2: Jack up vehicle and use jack stands for safety & remove the tire from the rotor.
Step 3: (Wheel alignment is necessary after strut replacement.) Marking the position of all the bolts will help
keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt.
Step 4: Use penetrating oil (such as WD40) to coat any rusted fasteners, let soak for approximately 1 hour.
Step 5: (Optional) While waiting for oil to soak, take this time to inspect all other components that may need
replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc).
Step 6: Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)!
Opening brake lines will require bleeding of the brake system.
Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in
expensive and time consuming repairs.
Step 7: Remove sway bar attached to the strut assembly or control arm.
Step 8: Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle).
Step 9: Remove the strut to knuckle bolts at the bottom of the strut. On some vehicles, the brake caliper and rotor
may need to be removed to gain access.
Step 10: Remove the upper mounting plate bolts located in the engine or trunk compartment. Do not remove the
center retaining nut! It is not safe to unload the spring from the assembly in this position.
Step 11: Carefully remove the old strut assembly from the vehicle. Be very cautious not to let the strut "drop" down
on your brake line, rotor or drum.
| Item Specifics | |
|---|---|
| Brand | BYUSCarparts |
| Manufacturer Part Number | 13455068 |
| Manufacturer Warranty | 1 Year |
| Type | Shock Absorber |
| Fitment Type | Direct Replacement |
| Manufacturer Warranty | 1 Year |
| Adjustable | No |
| Bundle Listing | Yes |
| Features | Sealed |
| Fitment Type | Direct Replacement |
| Gas Charged Shock | Yes |
| Custom Bundle | Yes |
| Modified Item | No |
| OE Spec or Performance/Custom | OE Spec |
| Surface Finish | Powder Coat |
| Kit Parts Included | Shock |
| Color | Black |
| Quantity | 4 |
| Shock Absorber System | Double Pipe |
| Material | Steel |
| Mounting Style | Screw-On |
| Placement on Vehicle | Front Rear Left Right |
If you have any question before buying the product, and any problem after getting the pacakge, do not hesitate to contact us.
2023 SALE
Shop Category Hot Item
New Arrival
Excellent Delivery
Picture  Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us |
 For 1991 1992 1993 1994 Ford Explorer 4.0L V6 Front Rear Struts Shocks
Fitment: 91-94 Ford Explorer NOTE: Look Above this product description (Item Specifics) for all part numbers, part brands, placement on vehicle and Compatibility.Make sure that is the correct fitment for your vehicle.
Features:
How to install: Step 1: Before you lift the vehicle, loosen lug nuts one full turn.
Step 2: Jack up vehicle and use jack stands for safety & remove the tire from the rotor.
Step 3: (Wheel alignment is necessary after strut replacement.) Marking the position of all the bolts will help keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt.
Step 4: Use penetrating oil (such as WD40) to coat any rusted fasteners, let soak for approximately 1 hour.
Step 5: (Optional) While waiting for oil to soak, take this time to inspect all other components that may need replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc).
Step 6: Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)! Opening brake lines will require bleeding of the brake system. Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in expensive and time consuming repairs.
Step 7: Remove sway bar attached to the strut assembly or control arm.
Step 8: Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle).
Step 9: Remove the strut to knuckle bolts at the bottom of the strut. On some vehicles, the brake caliper and rotor may need to be removed to gain access.
Step 10: Remove the upper mounting plate bolts located in the engine or trunk compartment. Do not remove the center retaining nut! It is not safe to unload the spring from the assembly in this position.
Step 11: Carefully remove the old strut assembly from the vehicle. Be very cautious not to let the strut "drop" down on your brake line, rotor or drum.
Payment
1. We accept payment which is accpeted by ebay. All payment above the picture that is accepted.
2. Before making a payment, please make sure that your address has been verified and is up to date. After the checkout is complete, we cannot change any address.
3. Please make sure you submit your correct address! Shipping
1. Product will be shipped within 2 business days after full payment is received and verified.
2. Delivery Time is about 3-7 business days to most of countries.
3. All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days.
4. We ship the package to your shipping address in eBay. Please tell us your shipping address if it is different from the one in eBay before we shipping the package.
5. The tracking number will be given for the customer to check the shipping status online (registered or faster service only).
6. We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout.
Returns
1. Defective products can be fully exchanged or refunded within 30 days after you receive the goods.
2. Any return or exchanged items must be in brand new condition and cannot affect resale.
3. The buyer is responsible for paying the return shipping fee or exchange shipping fee if it's not our problem.
4. Please contact us via eBay email before returning or exchange.
5. We only define the product as defective when it does not match the description or quality issue, and it is the buyer's responsibility to understand the product description before bidding.
6. If it cannot be replaced or the buyer wants a refund and returns the original ones at his own expense, we will refund the purchase price.
7. Transportation and handling costs are not refundable.
8. Man-made damage caused by abuse or misoperation is not covered by the warranty.
About us
We are committed to sell good car parts, and provide professional customer service to our customers.
1. We have new products on the shelves every week, you can follow our shop at any time, and you can browse and select products in the shop if you need it.
2. We treat every buyer with a sincere heart. We believe that our sincere service and excellent quality will win your trust and support. You can contact us by leaving a message, and we will reply within 24 hours from Monday to Saturday you. (Does not include local holidays)
3.Vehicle fittings are provided by product manufacturers and therefore may not be exact. If you receive a product from us that does not fit your vehicle, please contact us and we will try to assist you in finding the correct part and setting up an exchange.
Note
If you have any question before buying the product, and any problem after getting the pacakge, do not hesitate to contact us. All rights reserved. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
