FREE DELIVERY ON ALL UK ORDERS
100% POSITIVE FEEDBACK
UNBEATABLE CUSTOMER SUPPORTHAWK Performance DTC-50 Motorsports Brake Pads For Aerospace Components GT Caliper
Item Description
The Hawk DTC-50 compound is what racers have been asking for: a pad that can be used as a split compound for tuning, and an endurance compound that can be used at the highest levels of racing. DTC-50 was developed through extensive testing, giving racers a pad that enhances our line of Dynamic Torque Control products and bridges the temperature and brake torque range between our current DTC-30 to DTC-60 race pads. This new compound offers consistent performance across a wide range of temperatures, while providing very high torque and aggressive initial bite.
- Very High Torque
- Aggressive Initial Bite
- Excellent Modulation and Release Characteristics
- High Temperature Fade Resistance
- Designed for High Deceleration Rates
- 500-1100 Deg F Operating Temperature Range
- 500-1100 Deg F Optimal Temperature Range
For motorsport use only. Image is for illustative purposes, actual product may differ.
Hawk Brake Pad Installation Procedure
- Install Brake pads properly. Be sure pads are securely positioned in the caliper.
- Flush system with fresh brake fluid.
- Check all hydraulic parts for excess wear and tear.
- Check disc for proper thickness, parallelism, and lateral run-out.
- Check disc for scoring or grooves over .012"" depth. If either applies, resurfacing or replacement is required.
- If disc does not need resurfacing then contamination from the previous brake pads must be removed. Sand discs with Garnet sandpaper using moderate pressure. Use soap and water to clean off disc surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid
- Inspect calipers for freedom of movement. Lubricate where necessary
Hawk Brake Pad Bedding Procedure - Motorsports Pads
- After reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times.
- At higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times.
- At or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion.
- Do not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch.
- If during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal.
Important Reminders when Burnishing or Bedding Brake Pads
- Do not attempt to use badly worn or damaged rotors with new brake pads.
- Do not drag brakes while car is moving during break-in procedure.
- Do not engage pedal while car is stopped at any time following the break-in procedure.
- Upon completing the procedure, allow the brake system to completely cool before racing.
- Applying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds.
- Some forms of racing do not allow time for the proper break-in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible.
li>Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads
Limited Lifetime Warranty
Carlisle Brake & Friction (CBF) warrants Hawk Performance branded products to be free of defects from workmanship and materials. This warranty does not apply to normal wear or damage caused by negligence, lack of maintenance, accident, abnormal operations, or improper installation or service. CBF does not make any other warranty claims, either expressed or implied, including the implied warranties of merchantability or fitness for a particular purpose. In no event will CBF/Hawk Performance be liable for incidental or consequential damages of any kind, whether such damages are claimed on account of breach of warranty, breach of contract, negligence, or strict product liability. This includes without limitation, damage to property, or other economic losses that may be incurred. Any, and all, warranty claims must be processed through CBF. All valid warranty claims will be replaced and/or reimbursed with Hawk Performance branded products of equal or greater value.
* Disclaimer to Limited Life-Time Warranty: Motorsports brake pads and rotors are developed for high performance events. Racing is a dangerous sport. Hawk Performance racing brake pads and rotors are sold without warranty expressed or implied. No warranty or representation is made as to this products ability to protect the user from injury or death. The user assumes that risk.
Featured Categories
Payment Information
We accept the following payment methods:
Paypal, Credit, Debit Card, & Bank Transfer. All Auction and "Buy It Now" prices include VAT.
Shipping Information
What are the delivery charges for the UK?
| DELIVERY TO MAINLAND UK IS FREE. |
|---|
We send orders via a recorded delivery, which will require a signature on receipt. If there is nobody available at the delivery address to accept the delivery a card will be left to inform the recipient how he or she can collect the parcel.
PLEASE NOTE: A working day is Monday - Friday and doesn't include bank holidays..
Returns
Contact us prior to leaving negative feedback!.. Our Customer Service team will endevour to resolve any issues.
We offer a 14 working day returns and refund policy from the date of delivery in accordance to the DSR. You will receive the full refund to the value of the order (delivery costs not included).
The parcel must be returned in brand new condition, unopened and in the original packaging. The customer must bare the delivery cost of the return of the product/order.
This applies to all orders with us unless:
- Products that are ordered in error or that you changed your mind on will be entitled to a credit note at our discretion.
- Products that are faulty due to manufacturing process are entitled to a credit note under the manufacturers' warranty for a limited time specified in the manufacturer's terms and conditions (usually three months). If a product is credit noted due to manufacturing defects, the buyer is responsible for the return of the goods to such address as directed by the supplier. We will then offer you a credit note on return including all reasonable postage costs. This does not affect your statutory rights.
- Products that are damaged in transit to the customer CANNOT be refunded. If a product is damaged in transit the customer or recipient must NOT sign for the delivery. Instead the customer must refuse delivery by the courier and then contact us for further details.
