|
Item Description:
1. Guaranteed Exact Fit for easy installation
2. 100% BRAND NEW and tested to meet or exceed OEM specifications
3. Premium ISO/TS 16949 quality - guaranteed highest quality available
4. Engineered for superior durability, backed by industry leading warranty
5. These are brand new, not used or junkyard parts.
6. Each complete assembly is built to meet or exceed exact OEM specifications.
7. High corrosion resistance and long service life. Steel rod is mirco-polished with double chrome plate.
8. Newer Valving technology operates in stages based on the velocity of the car.
9. Use Teflon bonded piston seal to keep friction down and temperature cooler so that valving stays firmer.
Fitment:
2010-2010 Honda Fit 1.5L L4 1496cc 91 CID Hatchback FWD
2010-2011 Honda Fit 1.5L L4 1496cc 91 CID Hatchback FWD
2010-2012 Honda Fit 1.5L L4 1496cc 91 CID Hatchback FWD
2009-2009 Honda Fit 1.5L L4 1497cc Hatchback FWD
2009-2010 Honda Fit 1.5L L4 1497cc Hatchback FWD
2009-2011 Honda Fit 1.5L L4 1497cc Hatchback FWD
2009-2012 Honda Fit 1.5L L4 1497cc Hatchback FWD
Include:
2X Rear Struts （Rear Left Right）
Installation Notes:
Step 1:Before you lift the vehicle, loosen lug nuts one full turn.
Step 2:Jack up vehicle and use jack stands for safety & remove the tire from the rotor.
Step 3:(Wheel alignment is necessary after strut replacement.) Marking the position of all the bolts will help
keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt.
Step 4:Use penetrating oil (such as WD40) to coat any rusted fasteners, let soak for approximately 1 hour.
Step 5:(Optional) While waiting for oil to soak, take this time to inspect all other components that may need
replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc).
Step 6:Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)!
Opening brake lines will require bleeding of the brake system.
Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in
expensive and time consuming repairs.
Step 7:Remove sway bar attached to the strut assembly or control arm.
Step 8:Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle).
Step 9:Remove the strut to knuckle bolts at the bottom of the strut. On some vehicles, the brake caliper and rotor
may need to be removed to gain access.
Step 10:Remove the upper mounting plate bolts located in the engine or trunk compartment. Do not remove the
center retaining nut! It is not safe to unload the spring from the assembly in this position.
Step 11:Carefully remove the old strut assembly from the vehicle. Be very cautious not to let the strut "drop" down
on your brake line, rotor or drum.
Step 12:Install the new Complete Strut Assembly in the reverse order as above (steps 11-6). Using an anti-seize
compound on all fasteners is suggested.
Step 13:Carefully double check your work and make sure everything is tightened to manufacturers torque specifications.
Step 14:Replace the tire the rotor and tighten to manufacturers torque specifications.
Step 15:Slowly lower the vehicle down after removing the jack stands. Pay very close attention to any odd sounds
when the vehicle is lowered onto the new Complete Strut Assemblies.
Step 16:It is very important that you immediately "road test" your vehicle right away to ensure that installation was done properly.
Listen and feel for common signs of incorrect installation while driving slowly over speed bumps, rough road or potholes.
| Item Specifics | |
|---|---|
| Brand | wheeltech |
| Manufacturer Part Number | WH80901901P |
| Manufacturer Warranty | 1 Year |
| Adjustable | No |
| Bundle Listing | Yes |
| Features | Sealed |
| Fitment Type | Direct Replacement |
| Gas Charged Shock | Yes |
| Custom Bundle | Yes |
| Modified Item | No |
| Type | Strut & Shock Assembly Kit |
| Placement on Vehicle | Left,Right,Rear |
| OE Spec or Performance/Custom | OE Spec |
| Surface Finish | Powder Coat |
| Kit Parts Included | Shock |
| Color | Black |
| Compressed Length | 18.940"(R) |
| Extended Length | 23.620"(R) |
| Travel Length | 4.680"(R) |
| Interchange Part Number | AU348016 |
| Other Part Number | AU5682 |
| Quantity | 2 |
| Quantity | 2 |
1.We stand behind every product we sell.
2.All of our brand new items come with a 30-Days money-back guarantee.
Shop Category Hot Item
Excellent Delivery
Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us New List Item
|
Rear Left Right Shocks & Struts For 2009-2013 Honda 1.5L L4 1497cc Hatchback FWD
Item Description:
1. Guaranteed Exact Fit for easy installation 2. 100% BRAND NEW and tested to meet or exceed OEM specifications 3. Premium ISO/TS 16949 quality - guaranteed highest quality available
2010-2010 Honda Fit 1.5L L4 1496cc 91 CID Hatchback FWD 2010-2011 Honda Fit 1.5L L4 1496cc 91 CID Hatchback FWD 2010-2012 Honda Fit 1.5L L4 1496cc 91 CID Hatchback FWD 2009-2009 Honda Fit 1.5L L4 1497cc Hatchback FWD 2009-2010 Honda Fit 1.5L L4 1497cc Hatchback FWD 2009-2011 Honda Fit 1.5L L4 1497cc Hatchback FWD 2009-2012 Honda Fit 1.5L L4 1497cc Hatchback FWD
Include:
2X Rear Struts （Rear Left Right）
Installation Notes:
Step 2:Jack up vehicle and use jack stands for safety & remove the tire from the rotor.
Step 3:(Wheel alignment is necessary after strut replacement.) Marking the position of all the bolts will help keep the alignment close to original and save time aligning. Use a colored pencil to mark the old strut on the bolt.
Step 4:Use penetrating oil (such as WD40) to coat any rusted fasteners, let soak for approximately 1 hour.
Step 5:(Optional) While waiting for oil to soak, take this time to inspect all other components that may need replacement (brake pads, rotors, brake hoses, ball joints, CV boots, tie rod ends, bushings, sway bars, etc).
Step 6:Remove any brake line or wire attachments from the strut body. Do not disconnect brake lines (if possible)! Opening brake lines will require bleeding of the brake system. Use extreme caution when removing brake lines from your struts, as any damage to your brake line can result in expensive and time consuming repairs.
Step 7:Remove sway bar attached to the strut assembly or control arm.
Step 8:Remove the tie rod (only if it attached to the body of the strut, if not leave it attached to the steering knuckle).
Step 9:Remove the strut to knuckle bolts at the bottom of the strut. On some vehicles, the brake caliper and rotor may need to be removed to gain access.
Step 10:Remove the upper mounting plate bolts located in the engine or trunk compartment. Do not remove the center retaining nut! It is not safe to unload the spring from the assembly in this position.
Step 11:Carefully remove the old strut assembly from the vehicle. Be very cautious not to let the strut "drop" down on your brake line, rotor or drum.
Step 12:Install the new Complete Strut Assembly in the reverse order as above (steps 11-6). Using an anti-seize compound on all fasteners is suggested.
Step 13:Carefully double check your work and make sure everything is tightened to manufacturers torque specifications.
Step 14:Replace the tire the rotor and tighten to manufacturers torque specifications.
Step 15:Slowly lower the vehicle down after removing the jack stands. Pay very close attention to any odd sounds when the vehicle is lowered onto the new Complete Strut Assemblies.
Step 16:It is very important that you immediately "road test" your vehicle right away to ensure that installation was done properly. Listen and feel for common signs of incorrect installation while driving slowly over speed bumps, rough road or potholes.
1,We accept multiple payment methods.
2,Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay.
1,All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days.
2,The tracking number will be given for the customer to check the shipping status online (registered or faster service only).
3,We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout.
1.We stand behind every product we sell. 1,We stand behind every product we sell.
2,All of our brand new items come with a 30-Days money-back guarantee.
3,We define the item as defective only if it doesn't function as described.
4,It is the buyer's responsibility to understand the item description before bidding.
5,Man-made damage by abuse or wrong operation is not covered by this warranty.
6,No product liability insurance is assumed.
Q: How do I pay for my purchase?
A: MY store accepts multiple payment methods
Q: When will the item be shipped out?
A: This item will be shipped with 1 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My store accepts returns. Items must be returned within 30 days. Refunds will be given as money back. Please contact our customer service before you return an item.
wheeltech_All rights reserved. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
